Cleaning Talk - Professional Cleaning and Restoration Forum - Reply to Topic
Thread: Help!! Waxing problems Reply to Thread
Title:
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Cleaning Talk - Professional Cleaning and Restoration Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-30-2015 05:32 AM
Jeanannesunny The professionals at Jeananne Cleaning Services have the knowledge and qualifications to provide the highest quality buffing and waxing services for any type of floor. They are trained in the maintenance and restoration of all hardwood, tile, ceramic and vinyl floors.

* Remove all furnishings from the room and sweep the floor of all debris.
* Vacuum the solution from the scrubbed area.
* Repeat Steps 1 through 5 until the old wax has been removed from the entire floor. Allow the floor to dry completely.
* Repeat Step 7 to achieve three to four coats of wax.
01-27-2014 11:14 PM
ForeverClean Great Advice, I'm going to put it to Good use! Thanks Guys
04-14-2013 01:02 PM
kandiimeadows
Wax cracking or Separating

My floor care guys are also having this problem. The wax is cracking or separating after the first layer of wax is put on. One of them decided to wax an area without rinsing with neutral cleaner and he said is did not separate. What is causing the wax to separate. Does the neutral cleaner have to be used?
03-12-2013 04:13 PM
cmichael
Quote:
Originally Posted by SewClean View Post
Looking for a little insight as to a ploblem that we are having waxing laminate tile. Two years ago we striped, sealed and waxed two 200 sq ft bathrooms and a 1000 sq ft floor, everything went fine no problems. Now we are attempting to do the same over again. Started with the bathrooms, stripping went fine, sealer down and we started putting down thin layers of wax. First layer looked great, waited for it to dry then put down the second layer. Here's the problem; in only one of the bathrooms the second layer of wax when dry had what looked like spider web design cracks all over and when touched it flakes off. We have stopped everything for fear of it happening on the other floors!! Let me know if you know what causes this.
Answering the first question...

Could be a couple things here.
1). Wax could be contaminated by using same mop bucket as stripper, could be old wax, wax may have become frozen in weather at distribution point...
2). Stripper not completely rinsed or neutralized on the floor (most common problem, but usually you see the wax "fish-eye" or simply not drying)
3). If you used a neutralizer, it may have been under-diluted (too much neutralizer)
4). This may be a chemical reaction to the sealer you used or the sealer was not cured enough and mixed with the wax
5). If the floor is too soft, it can cause the finish to crack after you walk on it (this doesnt sound like your case)
6). Temperature or humidity is too high (or even too low)

Anyone want to add your thoughts?
02-09-2013 02:54 PM
jadmiral Its not a drying issue. The white spots are there when floor is completely stripped. Its as if there was a high spot there and the tile was sanded down.
02-07-2013 10:53 PM
WGEservice I think the problem was that there was not enough drying time. Bathrooms have a higher moisture content than other rooms
02-07-2013 10:42 PM
jadmiral
White spots on VCT, HELP

Helped a buddy strip a multi-colored brown vct floor. In some areas we "leaned-in" on the machine to completely strip. After waxing we notice that several of these spots have turned white as if we removed the color out of the tile. We have re-stripped and re coated with no luck. These white areas on the VCT will not turn dark. There is no color there. You would not notice this on a white VCT. It seems as if the tile was made with color only on the surface. Any suggestions on how to make those spots dark? We tried a brown marker after we stripped but it was the wrong brown. It would be almost impossible to find the right color brown since there are several shades in the tile.
John
02-07-2013 10:34 PM
jadmiral
Problem

nto enoght drying time. Bathrooms are notorious for this.
10-06-2012 01:48 AM
marie davidson Firstly, rinse the floor thoroughly to make it clean, Then apply the wax then wait for a longer time to let it dry and then and re-apply wax.
04-13-2011 02:47 AM
swarm
Quote:
Originally Posted by PCS View Post
This has happen to me. The finish could have dried to Quick. The temp of the floor cold. Here is a trouble shooting Guide. Good luck. Hope this helped. http://www.fullercommercial.com/trai...ting_guide.asp

Kitsap Floor Finish Supplies
only one type of wax. the em zine was not properly working
04-08-2011 02:20 AM
PCS This has happen to me. The finish could have dried to Quick. The temp of the floor cold. Here is a trouble shooting Guide. Good luck. Hope this helped. http://www.fullercommercial.com/trai...ting_guide.asp

Kitsap Floor Finish Supplies
01-04-2011 09:18 AM
ECBS I always look to see if you could have picked up a "contaminate" when waxing? Does the restroom have a mist air unit & was it on while waxing? We ran into this recently & it caused the wax to dry with an odd pattern. It was a top scrub & recoat. We had to strip it all off, shut of air unit & start over.
12-30-2010 01:14 PM
Rodgers12
repairing wax problems

Well there could be a few factors at works here. The most likely cause is the floor was not rinsed very well. I would recommend stripping the floor with a stripper, shop vac it all up, mop with hot water, then mop entire floor with a neutral cleaner. I would than mop the floor again with straight water.

This is a bit of a process but it will assure you that the floor is free of any substance that will affect the application and drying of the wax.
12-29-2010 01:54 PM
SewClean
Help!! Waxing problems

Looking for a little insight as to a ploblem that we are having waxing laminate tile. Two years ago we striped, sealed and waxed two 200 sq ft bathrooms and a 1000 sq ft floor, everything went fine no problems. Now we are attempting to do the same over again. Started with the bathrooms, stripping went fine, sealer down and we started putting down thin layers of wax. First layer looked great, waited for it to dry then put down the second layer. Here's the problem; in only one of the bathrooms the second layer of wax when dry had what looked like spider web design cracks all over and when touched it flakes off. We have stopped everything for fear of it happening on the other floors!! Let me know if you know what causes this.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome